I have a Photosonix NAVIGATOR stuck...
Posted: Tue Jul 18, 2017 22:50
Minmachine NAVIGATOR Photosonix stuck and will not turn on I press the power button only the led lights up and all, how to reboot?
But if charging stick and wait for 15 minutes?Мирас wrote:Minmachine NAVIGATOR Photosonix stuck and will not turn on I press the power button only the led lights up and all, how to reboot?
My GPS is not detected in device Manager...Алексей Крячко__ wrote:If with the AC adapter connected this occurs then..
You probably have the device set to programming. Then, when the enable indicator should illuminate on the top and there should be nothing on the screen. To get out of this situation after downloading the firmware in this device. The procedure is described
the instructions for programming
https://yadi.sk/i/qNad1QPM3LBaPr
The latest version of firmware 2.00
https://yadi.sk/d/I4urQYFRqRpCp
Manual to the latest firmware versions (2.00 and 2.01) :
https://yadi.sk/i/cmMskfT1qV4Cm
Software for your computer to load the firmware in the instrument (version 2.1)
https://yadi.sk/d/XhnbI8H1mndVB
Squeaking in headphones ? It can be if you headphones hooked up to the connector points. And would be a terrible squeak in the headphones, overload of the battery, it is possible the headphone output of the system. The first thing to do is to check the correctness of connection points and headphones.Ольга Ковкова wrote:What do you mean I have to any program, the same squeak? spooky squeak((
It never happened. WHY WRITE HERE WHEN YOU HAVE A SPECIAL THEME?viewtopic.php?f=38&t=5320Мирас wrote:PS. by the way can you send the link(s) for a full list of drivers and then I set a disk with drivers was not.
Алексей Крячко__ wrote:so, to summarize what I have at the moment :
The latest version of firmware 2.00
https://yadi.sk/d/I4urQYFRqRpCp
Manual to the latest firmware versions (2.00 and 2.01) :
https://yadi.sk/i/cmMskfT1qV4Cm
Software for your computer to load the firmware in the instrument (version 2.1)
https://yadi.sk/d/XhnbI8H1mndVB
About firmware 2.01 fixes : this firmware is programmed only in newly manufactured appliances, as it requires modifications of the hardware. Accordingly, in the previously released devices it makes no sense to write, so downloading it does not spread.
Difference 2.01 from 2.00 only possible to change the spectrum of the noise. Everything else is identical to version 2.00.
If you do not understand , call the office, we can help. You have not written what you have Navigator 1 second or a new (updated design)?<Алексей Крячко__ wrote:to change the firmware you need
1. download version 2.00 and unzip.
2. download the current program for updating the firmware (version 2.1)
3. to put a file embed_navigator_v200.bin there, where is the exe program file for flashing
4. edit the file f_write.txt instead of lines embed_navigator_v120.bin should be written embed_navigator_v200.bin
5. start navprog2n1.exe after set the device in programming mode and connect it to the USB, then turn on (on the device should be a blank screen, the backlight is lit and the orange led illuminated).
Because if you flashed Navigator 2 the firmware listed (as I pointed out, assuming that you have the 1st option, because they are by far the most common), then of course it won't work and to determine if the programmer is not (because after you activate the firmware, even incorrect, it exits programming mode and communication with the computer of course does not support). Then the only option is to transfer the device programming mode and hardware to re-flash the correct firmware. But can be certainly something with the device (firmware just without some action itself is not reset). Write your email address in personal messages, we will understand what to do next.ЛИЛИЯ-Р wrote: You have not written what you have Navigator 1 second or a new (updated design)?