Forum

Alexander (developer)
Thank you!
However, I have noticed that BEFORE I activated immediately after the delay (I did not picked up another volume and up), though I can't say that this time I had no dreams.

1. Are there people on which DreamStalker is not valid and what percentage of such people?
2. Help to decide what to choose DreamStalker or DreamStalker PRO? Never tried it, so I don't know whether I will have all these functions?
3. Are there any discounts? As for the province where the average salary of 8 000 -10 000 it is certainly expensive.

Зератул wrote:1. Are there people on which DreamStalker is not valid and what percentage of such people?

I don't think such people exist... But those who do not want to do it themselves and want the device do EVERYTHING for them, very much. They also have a good chance to use the device at full capacity, but often don't have the desire and patience - it's easier to start screaming at every corner that it is "quackery and divorce on the headstock"... it is Always easier to justify its drawbacks for others than work for them...

2. Help to decide what to choose DreamStalker or DreamStalker PRO? Never tried it, so I don't know whether I will have all these functions?

The PRO version is worth taking just because of the fact that she is a minute after the beginning of sleep without any flashes and beeps your calm voice to say, "it's just a dream" - in my opinion, is the most effective way to lucid for a beginner.

3. Are there any discounts? As for the province where the average salary of 8 000 -10 000 it is certainly expensive.

You can look for on the secondary market.

And where in Moscow it is possible to buy the device and it always has it in stock?

You can buy in our office or order delivery, there are always.

And the address of the office?

And the office as such is available? I'm just passing in Moscow, leaving in 2 days, wait and live in the suburbs, there is a place where you can come and buy the device? Called on the phone no one takes the tube (probably because that Sunday)..

The link provided has all the information about the office address, hours of operation, location map.
Sunday-day off.

Hello! I want to understand how to work the device. After the timer should trigger signals with a certain interval or after REM sleep should be signals? How is it regulated and what settings should I pay attention to?

Nikolay Kiev
Tips are issued after some time (1-2 min) after the start of phase BDG. This delay is not regulated. Most people are suitable settings to default (mode reset - SEtd).

Hello!
What would I wanted to recommendand here's the thing: I would recommend to cover all open contacts on the glass fiber lacquer or any other dielectric. We all know that water is weak but still is a conductor of electric current, I say this to the fact that when I took it overnight for a fee, fingers probably touched the contacts causing the appliance malfunctions has become another flicker of the image and sound became intermittent. I had to remove the batteries and insert them back after the device is started again to work normally.
In addition, all radio components are SMD components which they can careless hasty use of separating from the fiberglass.

And here actually and a question: I configured the device in the first mode of operation(intermittent signals 2s at detection of REM phase), as I later realized it worked for the night only once and then just after a certain interval of time was blinking and all looked the number of positives and was convinced that there was only one.
How do I configure the device that he would have worked every time when it detects the REM phase and not just once ? Last night instruction before sleep read because the device in the evening mail took, and configured as expected the timer is 2 hours 30 minutes, removed the sound, in the lower right corner have lit up the point(as expected). After that, went to sleep, it worked at 01:10 and once only, and then(don't know how often) it just blinked without the discovery of the REM phase.

Herman D.
Turn off the duplex mode and do not turn until you are comfortable.

Александр (разработчик) wrote:Herman D.
Turn off the duplex mode and do not turn until you are comfortable.

So I like it and is not included, unless it is enabled by default ? What value need to set ?

The value corresponding to the off state - 0. However, I would advise You to do a factory reset Setd and then nothing changes. It will all work.

And if you can adjust the time fast? I mean so wouldn't have to scroll through minutes in order to switch watch.

Herman D.
Press the button and hold. The minutes themselves will be rapidly scrolled.

Александр (разработчик) wrote:Herman D.
Press the button and hold. The minutes themselves will be rapidly scrolled.

Do so.

Today, again, why only one alarm and then blink after a certain interval.
At least go after a dream in CLtr and blinking in turns first u(inverted)001 and after 03.02(as I understand it this time).
Specifically went to menu and found the point du-0 - that is, the duplex is off.
I like this issue to be resolved ? the default settings are dumped before bed and put just the time and timer and still.

Герман Дмитриевич wrote:

Александр (разработчик) wrote:Herman D.
Press the button and hold. The minutes themselves will be rapidly scrolled.

Do so.

Today, again, why only one alarm and then blink after a certain interval.
At least go after a dream in CLtr and blinking in turns first u(inverted)001 and after 03.02(as I understand it this time).
Specifically went to menu and found the point du-0 - that is, the duplex is off.
I like this issue to be resolved ? the default settings are dumped before bed and put just the time and timer and still.

ugh, so sorry, I had to go to the Cotr and not in the CLtr. I'll try the brightness harder to do.

And another thing, here I made my settings the brightness of the LEDs but how do I check it ? CHUP checks only, and I need to check current settings.

Herman D.
Don't understand the question. If you need to check the settings, then go to settings and see what is installed there.

Александр (разработчик) wrote:Herman D.
Don't understand the question. If you need to check the settings, then go to settings and see what is installed there.

We have to see how bright will Shine the LEDs at a certain setting.

Mode CHUP shows real signals what they are. Melodic separator snooze at work will not play, of course.

Could you tell me what settings are used in the режимеUP-2? in addition to brightness-6 and duration-6, mean FR, OD, BR,F????

Attack
The more you change the settings without even reading the manuals, what it is, the worse the result will be. Because F is the duration of the series of outbreaks 6 seconds, BR - brightness level 6. If you do not see prompts during the sleep, go to manual settings and increase the duration to 20 seconds tips - immediately notice. Sound use is not necessary, you can add it only in the case when a person is sleeping, so that even though from a gun shoot. If it awakens, decrease the duration. Everything else do not touch, do default (Setd). In General, do not forget to train day and use better default settings, nothing is changing. The problem, if there is, it most often is in the mind, which is not adequately prepared to identify clues in the dream, not in the settings.