Forum

Шалтай Балтай wrote:

_Алекс_ wrote:I think you got to spin on the SP top)

can
can and bottom

_Алекс_ wrote:where discussed give a link?

In the same branch
slightly higher porabotala wheel
here: http://www.mindmachine.ru/viewtopic.php?p=55633#55633

Well, of course I saw it and I know that the coil is placed below the SP, I'm talking about the top guys!!!)

just above, parbattya wheel

and net of Kalesija, a large touchpad on the mac all the time to have all hands to do...))) waah)

_Алекс_ wrote:is placed below the SP, I'm talking about the top guys!!!)

can and bottom can and the top

Yes, it is possible to head to break with these directions))! But what if you don't get the ends to bend and to solder to them...balls and the middle one to post Here..like this:-[/br]
by the way, maybe a direction here truevue..in General, all these cropcircle - thing-in-itself, no matter how badly Here's an idea slipped: what if every complex structure(two-dimensional),to etch the foil on the Micarta, as the printed circuit Board, and then pour even packs?..Here, for the overall development http://oldoctober.com/ru/lut-naoborot/.(a desired image can be developed in Illustrator or CorelDRAW(shtob in the vector).

Ахмадинеджад wrote:to etch on the foil Micarta, as the PCB?..

I too think about it, especially

Шалтай Балтай wrote:and whether the guys are so muddied that spiral it is necessary to shake anyhow and Golden ratio?

but the WTO's already thrown the idea of HOW to do it: http://www.mindmachine.ru/viewtopic.php?p=57072#57072

OOO! Well, quite exhaustively, did not get back to this page)
About moju goldenratio to zaproponowali program PhiMatrix http://www.phimatrix.com/

and the idea was to fill holographic dot-matrix applicator type "Ayres". http://www.bio-lavka.kiev.ua/litairappl.shtml

Pour generally not necessarily
You can just put
So with the parlor doing.

Шалтай Балтай wrote:

Ахмадинеджад wrote:to etch on the foil Micarta, as the PCB?..

I too think about it, especially

Do something of the sort...
http://www.quantumbalancing.com/vortex_antenna.htm

However.. Impressive!! Thanks AK, study..
Here a couple of pictures similar in the text: http://fourthway.narod.ru/lib/rovner/gau4.htm

here and there eneagrama. porazitelno.

Here's something about which so long spoke bolshiviki (in my face)
well, my axe-dimensional version:


resources:
cable - 150 p (I think, maybe 50, not all were used)
- plastikowy glass (10? RUB)
- half an hour of work
well Atlanta, tape

there is an effect?
Yes while shaking his head beginning to lead as the first time
not included more
session prepare, there was finally an idea how to do it better

IMHO
The nodes are the simplest and most effective thing you can do with SP.
and it costs almost nothing for resources.
very recommend

PS
The original photo of the "cake" here: http://www.mindmachine.ru/viewtopic.php?t=3295
already months 9 to him. Potryasayuschaya thing

The number of turns important?
Why the top sheet of paper?


Sincerely, MAG.no

Маг.нет wrote:Why on top of a sheet of paper?

I think this is a normal link.

Thank you!
Then another question: the glass bottom is? And for what purpose the duct tape?


Sincerely, MAG.no

Маг.нет wrote: And the purposes for which duct tape?

I guess that the cable is not unwound...

So it seems under the glass is not unwound...
What's with the wire ends? Simply cut off the "under spring"?


Sincerely, MAG.no

Маг.нет wrote:the Number of turns important?

if You think that it is Sacmi, so it may be so for You

Логик wrote:I think this is a normal link.

Yes
well, or the table of links

Маг.нет wrote:the glass bottom is?

no, there is a bar code

Маг.нет wrote:What's with the wire ends?

Simply cut off

Thank you! Thought know-how),and found a review of efficiency:)

Шалтай Балтай wrote:bar code

???

Sincerely, MAG.no

Hatching, which is on the table quite unnecessary.

How interesting it would be to order the nodes at a third-party company? On the market there are services for the production of wire products. But as I understand it for 10-15 products, they will not take. ACC. right amount of several hundred pieces. If there are 10-15 people interested, we can try to place an order.
Are you interested?

I'd think about these:

pieces 15-20.

Are easier hands to turn with pliers... For ten minutes 6 pieces out of the wires in the elbow are long.

к-13 wrote:Are easier hands to turn with pliers... For ten minutes 6 pieces out of the wires in the elbow are long.

link Sachs
well, let's
Can the same smooth to do, but in a diameter of 20 cm, better 30?
Will take pleasure (not for free of course)

However it is better in PM...

Шалтай Балтай wrote:link Sachs

I'll fix that.

well, let's
Can the same smooth to do, but in a diameter of 20 cm, better 30?
Will take pleasure (not for free of course)

However it is better in PM...

Yes not especially it and even in the photo... I have an interesting result, and in payment I'm not really zainteresovan(especially because labor costs are minimal).
You can and here's a site to stir up(he is also a working flower the bloom began, and then almost dried up )
[/url]

к-13 wrote: You can and here's a site to stir up(he is also a working flower the bloom began, and then almost dried up )
[/url]

no, it's not necessary, sorry.
the spiral is not flat, monogram not clear destination
and form, Hz. what to do with it
and besides counterclockwise
needs such as in the photo above.
if you want to complicate, it is better to take the wire to twist into a spiral (pigtail), and from this spiral - untie the knot.
that's interesting