Reprogramming of the device. New firmware version

[Алексей Крячко__]

- During charging, spontaneously starts playing music The moment when the music Navigator "chooses" himself. Sometimes when charging is finished the red indicator light goes out, but the power cord remains connected, sometimes directly in the charging process. A couple of times was that the music involved just by itself when the device was turned off.

most likely your device has been enabled, but was in standby mode. When you turn off the device physically has no power of piezodynamic and everything else.
And worked there just an alarm clock, probably in the morning, hours at 9-10 am. To avoid this, I recommend to go to Alarm->alarm Mode. And using the keys "right"-"left" to navigate through the menus by day of the week and clean icons "+" by pressing "up" or "down". Now all newly manufactured devices in the default settings for all the days the alarm is off, and was formerly included except Saturday and Sunday.
must also be deactivated and a timer which can start the tune (about this in detail in the instructions).

- Reset session, ie not play out to the end. You might think that the charge accum. low, but when you turn the power cord, the red indicator lights up... When you re-enable session to discharge accum., session play out until the end After charging works.

Batteries native, was only used in Navigator and only all together

after two years of using batteries found such a problem, and Focus on ray and Flex power. Before discharge they have greatly "failed" the stress, then restored when loading again, and after that they are discharged to the end.

Can't recommend on a new set of batteries first 3-4 cycle to carry out the discharge until the end. Avoiding "surprises" (in the form of terminating sessions) can be targeted discharge when the battery icon you will see the filling below half, after another successful class. Enough to run the session or audio file and press the "II" (stop). headset and glasses can be disabled to not interfere and the device to forget. after some time after the discharge of the batteries, the device itself will reset the playback and go into a low power mode. Then turn it off, connect the network adapter on. To begin the battery charge.

the same operation can be done on already working about a year or more batteries. Or in the device to discharge, or in a special charger that is NiMh battery can discharge before charging. You who is there. This procedure allows you to remove the memory effect, helps to increase effective capacity on used batteries.

In the device, of course, the condition of the batteries and their life is difficult to trace, given that it is NiMh. However, there are some algorithms that I will try in the future to include in the next firmware. To work out all of them and test on different batteries is of course time.<

[Андрей Патрушев]

Alexey Kryachko__
I remember in the years of perestroika, when bloomed cooperatives, produced a battery charger with a rectangular asymmetrical alternating current. It allowed to safely (including by reducing the required charging voltage) to charge the batteries even (three times up to 80% of the nominal value) and significantly reduced charging time of the battery. The point is that the backflow was allowed to remove the polarization on the electrodes (destroying the electric double layer). The ratio of the charging current and counter-current, is about 63/37, but the frequency (depends on the speed of formation of the electric double layer), unfortunately, I do not remember. It probably is possible somehow to experimentally pick up - sharp (and maybe a smooth ) drop resistance, for example. And maybe the frequency as the time standard, and everything is determined by the ratio of forward and reverse current...

[Стаc Док]

Alexey Kryachko: Good health Alex! I understand that under the "Windows 7" (64 bit) AT 1.16 and is running and working (now) without any problems?

[Алексей Крячко__]

Alexey Kryachko: Good health Alex! I understand that under the "Windows 7" (64 bit) AT 1.16 and is running and working (now) without any problems?

under win7 64-bit is a program for flashing the device works, it can download version 1.16*. Something like that. Now only one bug found - is it in English version of win has no Russian letters in the program, but its performance is not affected, everything is programmed. Fonts which are not in English versions of win I will add.

[Алексей Крячко__]

Andrew, unfortunately NiMh batteries now have some coverage of the electrodes themselves which does not allow ripple current (especially a reverse polarity). Only DC and(or) long pulses of constant current.

[Андрей Патрушев]

[Кирилл.]

Good afternoon.

I have stopped working decoder, while playing the gate records for a couple of seconds the icon appears on the square, and then just disappears. No sound, no flicker in the glasses is not.

Previously, everything worked fine, the problem appeared after the next play has been stopped due to low charge of the accumulator - the power cord is connected, but to run no longer possible. Version 1.16.

[Кирилл.]

Good day,

You can get some review on solving the problem? Three weeks have passed.

[Андрей Патрушев]

Cyril.
It was better via PM, or by e-mail to ask Alexey Kryachko.

[Алексей Крячко__]

today I wills how to solve the problem.
I repeat here, because the case of the model. Unfortunately out of the house last time writing on a forum does not work

After the failure of under-voltage, always switch off the appliance by pressing the power button, connect the AC adapter and then turn the power button on the keyboard. If the power adapter is connected after switching on the device, when discharged batteries may not work gate decoder and no sound - this is normal behavior. (strobe decoder and audio off in all new firmware versions when discharged batteries because most consume current)

if these recommendations in order to enable the device do not help to restore the normal operation of the gate decoder, we will continue to investigate it.

[Кирилл.]

if these recommendations in order to enable the device do not help to restore the normal operation of the gate decoder, we will continue to investigate it.

Unfortunately, these recommendations do not help, change does not happen no.

[Алексей Крячко__]

wrote a personal message but will copy here, if the problem is still have any
Hello, Cyril. questions equipment it is better to send by e-mail, they're fast enough in this case transmitted. Here, I can unfortunately quickly view and reply.

let's explore in more detail what could be crashing.
There are 2 probable causes : corrupt data on the memory card and malfunction of the player
1. The player can be checked on any mp3 or wav file. If they are not played back (with headphones silence), it won't work and strobe decoder.
In this case the screen will be a progress bar of playback. You need to check the volume setting by pressing "up" to set the volume of the player P45, primary keys adjust the volume level 30-33. It happened that after the emergency exit due to low power reset it settings the volume level of the player and everything stopped working (there was silence).
2. actually the strobe decoder. You can check from menu "Training" -> "Gate decoder".
if you have the ability to play a gate-entry (for example, computer "green" (linear) output). To install while on the computer the volume level to approximately 75% (2/3 of scale, volume)
Computer output connect to the input of the device (marked with "->O") using audioscore that comes in the kit.

if both items are performance and memory gate-the entry still does not play, it is recommended to install another map on which to move the gate-the entry to the folder "STROBE"

well, one more thing : when entering the "Player" in the lower right corner should be E|C|xx, where xx is a number from 45 to 50. But in any case not less than 45 and not 0 - then the strobe decoder will not work.

if it fails in any of these items to achieve the operation of the device, and the device is still under warranty - you can exchange it under warranty.

[Алексей Крячко__]

to ALL

In the device, of course, the condition of the batteries and their life is difficult to trace, given that it is NiMh. However, there are some algorithms that I will try in the future to include in the next firmware. To work out all of them and test on different batteries is of course time.

as a result of various tests and experiments with different sets of batteries decided to version 2.00 to do so :
- remember the state of the battery if a failure occurs and always after this failure include the charger and already at full charging current to battery test.
- to enter in the menu "manual" switching on the charger as it was in older versions. It already to absolutely surely could attempt to charge even dead batteries with very low capacity.

the new firmware will be released in late may-early June, now produce its testing and revision.

[Ростислав]

already more than beginning of June)))

[Воффка]

Alexey Kryachko__
Hello!
Tell me, when will the new firmware version?

[Алексей Крячко__]

Good day to all.
There is new version of firmware.
http://www.mindmachine.ru/download/navi ... r_v120.bin

in fact it is version 1.16 which removed some bugs and added the ability to manually turn on the charger for the specified time as it was in all versions prior to 1.16. However, the automatic inclusion of z.from. also left behind. If the threshold auto s.from. passes and the charger starts working, then manually to turn it on or off makes no sense. The possibility of including manually left for the use cases are too old or too new battery that already (still) small capacity.
In addition, with version 1.20 changes work with the combined sessions (the audio). The old combs. session will be played with this firmware and previous versions, but the new combs. session only with version 1.20 and later.

[Дмитрий Никитин]

Hello! Thank you! Pereproshivka. I thought, or the sound of the sessions became deeper? As if changed EQ settings?

[МОЛЧУН]

Alexey Kryachko
Is it possible this program to fill v-120?
What you need for this?

[Путешественник]

The new firmware detected a small bug: in some cases (sometimes) when you start the sessions after increasing the sound level in the first segment does not match the specified parameters.

Still no possibility to smoothly change the sound volume from segment to segment.

[Алексей Крячко__]

In the new firmware discovered a small bug: in some cases (sometimes) when you start the sessions after increasing the sound level in the first segment does not match the specified parameters.

Still no possibility to smoothly change the sound volume from segment to segment.

the volume of the segments should be agreed when programming. Or insert transitional segments with the increase of sound by 10% and a minimum time duration.
What is the setting in the sound does not match for the 1st segment ? You also need to consider the inclusion of slow modulation of the sound, very often incorrect programming of the parameters of the slow modulation leads to jumps in sound volume when switching from segment to segment.

[Алексей Крячко__]

significant alterations in sound in this version was not changing the EQ settings... it has a view of audio file playback ? some settings were changed on mp3 but on hearing it is impossible to estimate in General.

[Путешественник]

Hello.

Which option in the sound does not match for the 1st segment ?

The volume. In one of the channels from any one sound carrier is increased to 100%, what would the volume have not been exhibited in the segment. Is either to listen or to stop the session and start again. When you restart the sound, as a rule, normal. The error occurred 6 times within 18-20 days (I am using the device 2 times a day).

the volume of the segments should be agreed when programming. Or insert transitional segments with the increase of sound by 10% and a minimum time duration.

This is very inconvenient as become noticeable noticeable abrupt amplitude changes. Very desirable would be to set editor to "smoothly" might be applicable also to the brightness of light and the amplitude of the acoustic signal.

And I would very much like to see in the next firmware versions of the device and the program editor has the opportunity to control the device directly from the editor window with the ability to play any of the segments of the created session. It would really simplified the process of programming of the device and protect the user from accidental errors.

[МОЛЧУН]

Alexey Kryachko.
The problem with the batteries.
Pereproshivka 1.20 on how to enter the manual control mode charging?

[Дмитрий Никитин]

significant alterations in sound in this version was not changing the EQ settings... it has a view of audio file playback ? some settings were changed on mp3 but on hearing it is impossible to estimate in General.

Yes, that's right. Session (audio) which I did in Neuroprogrammer began to sound somewhat blurry...Deeply...and became in my opinion not as effective as before Until I rolled back to version 1.16

[Алексей Крячко__]

Alexey Kryachko.
The problem with the batteries.
Pereproshivka 1.20 on how to enter the manual control mode charging?

simply click "start" on the icon of the battery (it is available in menu). And then to set the desired time and then press again "start". Default time is 9 hours, which is normal for most batteries with a capacity of 1800-2200 mAh. Re-entry into pictogramme and pressing "start" turns off the charger - if it suddenly turned on by mistake.