Stabilizer.

Post by **Андрей Кабанков** » Thu Jul 07, 2011 22:30

Stop the Magic
Keychain 2900 RUB
Glass disc, 60 mm 3900 RUB.

Post by **Михаил_** » Thu Jul 07, 2011 23:06

Маг.нет wrote:.Buy FOB StopMagicissue is - this "set of software" would like something to interact with my Stabilizer, will my Stabilizer to strengthen the capacity of key FOB?
Would it be possible to place the "eye" of the keychain as "stack programs" directly on "one of..." anchors of my Stabilizer, does it increase the capacity or manifestation of the programs in this adjustment of the processes/objects?

Sincerely, MAG.no

everything is exactly the same as if it were a regular program on plastic - i.e., Yes, it will, Yes it can be placed and so on. Well, Yes, it is somewhat stronger than the usual plastic (weight, technology), but is a stack of programs.

PS Perhaps the first party trinkets will be rectangular, due to the fact that the production of round billets temporarily (weeks two-three).

Петрос · Post by **Петрос** » Thu Jul 07, 2011 23:36

Michael_
Why is this stack of programs?

Борис_ · Post by **Борис_** » Fri Jul 08, 2011 17:40

What area is better to put the anchor on the Internet - something he would have normally worked (And all the time any glitches)?

Maybe even an anchor on the provider - he is broken on the line then something else...?

Post by **Михаил_** » Sat Jul 09, 2011 13:53

Петрос wrote:Michael_
Why is this stack of programs?

well, the people asked stoppage.
and in the glass a lot of places

this set of programs goes well with stepmania and its complement, acting in the same direction, ie, providing greater stability overall.

Post by **Михаил_** » Sat Jul 09, 2011 14:14

Well, you can put the anchor under the description "my Internet" with prog. additional stabilization in the area between creativity and braking somewhere.

Петрос · Post by **Петрос** » Sun Jul 10, 2011 1:43

Михаил_ wrote:and in the glass a lot of places Smile

Post by **Михаил_** » Sun Jul 10, 2011 11:21

while temporarily stoppage comes in a rectangular trinkets - the-blanks another type of temporarily out of the country, the functionality is not affected. The round will appear probably before the end of the month.

Post by **Маг.нет** » Sun Jul 10, 2011 12:50

And here I got good timing:)I have a round key FOB:)

Sincerely, MAG.no

Post by **Михаил_** » Sun Jul 10, 2011 13:00

yeah, he was the only one in the party

Петрос · Post by **Петрос** » Sun Jul 17, 2011 17:20

Did your stabilizer. I Express my deep gratitude for your responses to my questions, good suggestions and opinions, clarifications, conversations, the process of creating the artifact Master. Tao Of MAG. no Logik. Michael thanks for the opportunity to do such a thing with their hands.

Post by **Маг.нет** » Sun Jul 17, 2011 17:35

Sincerely, MAG.no

Логик · Post by **Логик** » Mon Jul 18, 2011 22:21

Michael, and you can explain what's so good about a laser for making images and why a simple printout weaker? Can the laser engraving be replaced by another technology? By etching for example?

Post by **Михаил_** » Tue Jul 19, 2011 0:29

the laser is a unique not quite a physical process.
Other unique processes, but they are not suitable as laser. An indirect explanation of the example can be taken from the same book "This digital world", the author of which I was a little pararakelse in the literature. That is, as the explanation is not rolled, but how bold some of the special effects in the area, not just light, but a laser including phenomena - rolled.
We, in the case of the laser, the figure is not important at all. Ie it is important at the stage of processing (charge to speak actually not right! for this case) as the path, but you can erase it altogether, or laser can not leave a visible trace is not important. Important scattering power and the equivalent path as a process of combining on the holographic principle.
We can say that the other, but this does not mean that more effective method - it is actually holography (as I understand it, it is for example used in products LIK). There are others, but from scrap - the laser is the easiest and most effective.
An important power that is not important visually distinct mark. And it is important that the drawing was reproduced trajectories, not raster.
Maybe a combination of technologies, but that they simply not be

ie for example you can run the engraving of the hologram or to illuminate the hologram with a laser. As it should be. You know, it's not easy. Symmetrical to the laser pole will be sound effects, but there are other requirements to a signal and to create the right one will not be easier, and much more difficult.
In General, some clarification on this subject is on the website of my colleague who created the modulator. Although there is not a very simple language it contained.

Стэллари · Post by **Стэллари** » Tue Jul 19, 2011 12:06

after pouring the epoxy stabilizer is a part of the pieces of wax were left projecting above the surface. how best to proceed? carefully cut off the protruding parts, or even fill with epoxy, or leave as is? in principle, I would leave as is, but would be awkward on top of the print to stick. they just do necessarily on top of the epoxy once again to glue? I just got the epoxy is transparent, and all pasted underneath the print clearly visible)
and wax lightly sailed in the area of the Homo, what to do with him there?
the epoxy is frozen already)

Петрос · Post by **Петрос** » Tue Jul 19, 2011 14:41

A similar case was with me. Put the border on the hardened epoxy. While indeed the border had to stick on an uneven surface where the wax acted. The top filled with another layer of epoxy and then I glued the border and covered them with a thin layer of epoxy as a drying material. It turned out the sandwich. Two coats of epoxy and three layers of borders.

Стэллари · Post by **Стэллари** » Tue Jul 19, 2011 15:19

with three layers of slaughter probably happened)) and I'm still not a magician, and just learning... I slaughter probably too early))
but option thanks)

Post by **Михаил_** » Tue Jul 19, 2011 22:15

Стэллари wrote:after pouring the epoxy stabilizer is a part of the pieces of wax were left projecting above the surface. how best to proceed? carefully cut off the protruding parts, or even fill with epoxy, or leave as is? in principle, I would leave as is, but would be awkward on top of the print to stick. they just do necessarily on top of the epoxy once again to glue? I just got the epoxy is transparent, and all pasted underneath the print clearly visible)
and wax lightly sailed in the area of the Homo, what to do with him there?
the epoxy is frozen already)

I also frequent speaker.
The glue on top, fine.
What has shifted is okay too.. so to say the individual features of the device.

Стэллари · Post by **Стэллари** » Tue Jul 19, 2011 23:57

so leave as is, and labels on top to stick.
thank you)

Алексc3000 · Post by **Алексc3000** » Fri Jul 22, 2011 0:40

Good day, reach the clay (so many rivers, lakes and springs have traveled You have no idea) but still found and Zatar thoroughly for the future, in the description it is written that all stabilizer components are added to the epoxy resin in the least when the resin is filled into the tray, I have from manufacture of cakes left, polyester resin, so I want it for the manufacture of the device to use if it will fit, Politika did not know how to boil what would the thickness of the layer was not really fast enough freezes well and moderately heats up during solidification, poliefiry different from the epoxy resin, greater fluidity it is almost like water when it salivates anything that it seeps in almost all the cracks, so I want the components before pouring the clay and wax (will be in the form of small pieces, lumps) place in the zones of the first tray and then carefully pour the whole thing polièfirkoj, do you think you can do that? (should I still get really wax may slightly go)

Post by **Михаил_** » Fri Jul 22, 2011 2:21

Yes, it can be done.

Post by **Маг.нет** » Sat Jul 23, 2011 11:00

My StopMagic not worth more than is on the way:).......
The package was opened (this has never happened before, when hundreds of the parcels via EMS), BUT all in one piece and... found that yesterday evening (most likely after opening mine, because my parcel is in the processing was yesterday, informed theft in our EMS was observed and access to parcels after the discovery of the theft of the officer has been restricted) was caught on the other sending them a new employee is a trainee working the first week of may my package slid him to the Law, though, and take it from her nothing could, putting his hand to push the seam, turned over in full, BUT

not reached... More opened packages is not detected.
Promised that this will never happen again:)the opportunity came accidentally, in connection with the repair.

Sincerely, MAG.no

Алексc3000 · Post by **Алексc3000** » Wed Jul 27, 2011 23:54

Good day, after charging Druze stabilizer left 8 liters of water structured today bought wax natural with Pasika, I want this wax just in case clean, as I think if the melted wax to pour into this structured water then will it be possible to use it in the stabilizer and clean it?
The water is generally some sort of tricky get me N 3.0 a couple of months stood at all not even smell the beginning, so almost evaporated.

Алексc3000 · Post by **Алексc3000** » Thu Jul 28, 2011 13:15

Did today what he wanted, interestny wax turned out, became brittle scales breaks down when the hand piece is nice kept warm

димыч · Post by **димыч** » Thu Jul 28, 2011 14:13

how did you make the water 3.0 N? bottle chtoli mandala wrapped? I have a round vessel, I'm in it twice bracelets charged 1.0, now painted his matrices 3.0 L,
put black flint and quartz for water purification, the water you drink and the plants are sprayed