Converter USB-COM
Recently purchased Converter USB-COM for upload sessions Innerpulse via USB port. Installed the necessary drivers, but the program Light/Sound Librarian determines the presence of 4 COM ports that do not want to find a device connected via a Converter to USB.
Note. The system has 6 USB ports and 2 legacy COM ports through one of which the session loaded without any problems. But still for me it is more convenient to use a USB, to the same COM port occupied by the modem, and messing around with plugs and screws every time is not desirable.
And especially now, not everyone has COM ports and this question is relevant.
Note. The system has 6 USB ports and 2 legacy COM ports through one of which the session loaded without any problems. But still for me it is more convenient to use a USB, to the same COM port occupied by the modem, and messing around with plugs and screws every time is not desirable.
And especially now, not everyone has COM ports and this question is relevant.
Einstein
And tell me where it is sold?
And then I have a wire to the computer that came in the kit to mindmachine, does not fit to the laptop. I would like to buy this wire, to one side of sterek to mindmachine, and on the other USB ports. COM port - what is it?
And if I am posting to buy does not arise if I had difficulty pumping with the laptop in the car, as You have.
Session Patrushev want to download morning and evening, well and disks are Healing and the Conductor listen via mindmachine.
Thank you.
And tell me where it is sold?
And then I have a wire to the computer that came in the kit to mindmachine, does not fit to the laptop. I would like to buy this wire, to one side of sterek to mindmachine, and on the other USB ports. COM port - what is it?
And if I am posting to buy does not arise if I had difficulty pumping with the laptop in the car, as You have.
Session Patrushev want to download morning and evening, well and disks are Healing and the Conductor listen via mindmachine.
Thank you.
-
- Автор сайта
- Posts:10238
- Joined:Tue May 30, 2006 20:17
- Location:Екатеринбург
- Has thanked: 134 times
- Been thanked: 556 times
- Contact:
Re: Converter USB-COM
That's right - the system polls the COM ports at addresses, not USB. But if you approach this issue seriously, then downloaded the session You will need approximately three weeks, so "everytime" You will have to not happen so often.Эйнштейн wrote:To buy Converter USB-COM for upload sessions Innerpulse via USB port. Installed the necessary drivers, but the program Light/Sound Librarian determines the presence of 4 COM ports that do not want to find a device connected via a Converter to USB.
Note. The system has 6 USB ports and 2 legacy COM ports through one of which the session loaded without any problems. But still for me it is more convenient to use a USB, to the same COM port occupied by the modem, and messing around with plugs and screws every time is not desirable.
And especially now, not everyone has COM ports and this question is relevant.
- Князевский
- Posts:304
- Joined:Sat Jul 28, 2007 21:12
- Location:посёлок "ЗАРЯ"
Re: Converter USB-COM
Little understood, so that YUSB on WHOM has no real use?
Sorry, I too want his mind to buy a car. But without the ability to change anything for me, no device - no device, and without loading new sessions, I did not do (and then, of course, once mastered). So if I want to buy InnerPulse, but on my computer there is no COM port, adapter USB-COM useless? And I completely lose all the joys download new sessions?
Hello.
Maybe my message is no longer relevant, but still write, maybe someone should.
The USB-COM adapters are sold in any computer lounge.
Long with it suffered, defined as a COM 20 and more.
And LSlib only 1,2,3,4 –COM ports.
Nothing intelligible about this problem said.
Found how to solve it, was simple.
Go to device Manager select ports(COM & LPT) there should be determined
transition USB-COM. Open the properties tab: port settings – advanced
you have the option to change the port number to select free from 1 to 4 if busy
can renaming to the desired port free for our purpose.
And that's all. Good luck to everyone.
Maybe my message is no longer relevant, but still write, maybe someone should.
The USB-COM adapters are sold in any computer lounge.
Long with it suffered, defined as a COM 20 and more.
And LSlib only 1,2,3,4 –COM ports.
Nothing intelligible about this problem said.
Found how to solve it, was simple.
Go to device Manager select ports(COM & LPT) there should be determined
transition USB-COM. Open the properties tab: port settings – advanced
you have the option to change the port number to select free from 1 to 4 if busy
can renaming to the desired port free for our purpose.
And that's all. Good luck to everyone.
-
- Автор сайта
- Posts:10238
- Joined:Tue May 30, 2006 20:17
- Location:Екатеринбург
- Has thanked: 134 times
- Been thanked: 556 times
- Contact:
Thank you very much!Алекс405 wrote:Hello.
Maybe my message is no longer relevant, but still write, maybe someone should.
The USB-COM adapters are sold in any computer lounge.
Long with it suffered, defined as a COM 20 and more.
And LSlib only 1,2,3,4 –COM ports.
Nothing intelligible about this problem said.
Found how to solve it, was simple.
Go to device Manager select ports(COM & LPT) there should be determined
transition USB-COM. Open the properties tab: port settings – advanced
you have the option to change the port number to select free from 1 to 4 if busy
can renaming to the desired port free for our purpose.
And that's all. Good luck to everyone.
With Your permission will move Your post to the manual.
Re: Converter USB-COM
Good day! Q razrabotchikom
please tell me, is it possible to purchase separately date cable to download sessions for machine inner pulse.
Happened byada lost original com cable, cat. I went complete with a mind machine. in retail, in principle, such cables do not exist.
HELP! I will be very grateful for your help, it would be the best example after sales customer service.
(just in case, I still have the warranty card and the required documentation for mind machine).
please tell me, is it possible to purchase separately date cable to download sessions for machine inner pulse.
Happened byada lost original com cable, cat. I went complete with a mind machine. in retail, in principle, such cables do not exist.
HELP! I will be very grateful for your help, it would be the best example after sales customer service.
(just in case, I still have the warranty card and the required documentation for mind machine).
- ЛИЛИЯ-Р
- Posts:3002
- Joined:Thu Oct 11, 2007 21:25
- Location:Москва
- Has thanked: 478 times
- Been thanked: 264 times
Re: Converter USB-COM
гость3 wrote:Good day! Q razrabotcheskogo please, is it possible to purchase separately date cable to download sessions for machine inner pulse.
The cable can be purchased from us ,the price of 300 rubles.
Re: Converter USB-COM
Hello
I also have here a similar situation as n
Finally got the adapter, I took a USB-RS232 (USB Cable, VCOM VUS7050, USB A (m) - 9pin COM (m) 1.2 m)
,
all set up, hooked up Innerpulse, ran it, added a few sessions of A. Patrushev, pressed "Download Library (Append)"as was written "you will see the fun of running lights to your car"it was also but then on the display the number of established sessions, and "FnA"
well, that is, in the end, the session is not loaded, there is no section u
what to do? how to be? please tell me
I also have here a similar situation as n
Finally got the adapter, I took a USB-RS232 (USB Cable, VCOM VUS7050, USB A (m) - 9pin COM (m) 1.2 m)
,
all set up, hooked up Innerpulse, ran it, added a few sessions of A. Patrushev, pressed "Download Library (Append)"as was written "you will see the fun of running lights to your car"it was also but then on the display the number of established sessions, and "FnA"
well, that is, in the end, the session is not loaded, there is no section u
what to do? how to be? please tell me
-
- Автор сайта
- Posts:10238
- Joined:Tue May 30, 2006 20:17
- Location:Екатеринбург
- Has thanked: 134 times
- Been thanked: 556 times
- Contact:
Re: Converter USB-COM
Amauri
And You through LSD or through the Library loaded? Port what number is it assigned?
And You through LSD or through the Library loaded? Port what number is it assigned?
-
- Автор сайта
- Posts:10238
- Joined:Tue May 30, 2006 20:17
- Location:Екатеринбург
- Has thanked: 134 times
- Been thanked: 556 times
- Contact:
Re: Converter USB-COM
Amauri
And the mode is append or Clear?
Accordingly, the total capacity of all the loaded sessions corresponds to the free space in the car?
The car, apparently, decided correctly and in the Device line is Your brand?
And the mode is append or Clear?
Accordingly, the total capacity of all the loaded sessions corresponds to the free space in the car?
The car, apparently, decided correctly and in the Device line is Your brand?
Re: Converter USB-COM
just to make sure I tried all of these items:Андрей Патрушев wrote:Amauri
And the mode is append or Clear?
Accordingly, the total capacity of all the loaded sessions corresponds to the free space in the car?
The car, apparently, decided correctly and in the Device line is Your brand?
Download Session(Append)
Download Library (Append)
Download Session(Clear)
Download Library (Clear)
Yes, do not exceed loading capacity...
and the brand has exhibited Innerpulse
And maybe to try LSD?
Maybe still a problem in this adapter?
-
- Автор сайта
- Posts:10238
- Joined:Tue May 30, 2006 20:17
- Location:Екатеринбург
- Has thanked: 134 times
- Been thanked: 556 times
- Contact:
Re: Converter USB-COM
Amauri
Well, I don't know what to do. I, in General, not a specialist in computers.
Oh yeah, one more thing - machine should be powered from the adapter, not on batteries.
Well, I don't know what to do. I, in General, not a specialist in computers.
Oh yeah, one more thing - machine should be powered from the adapter, not on batteries.
Re: Converter USB-COM
Andrei Patrushev
Yes, I did, from the adapter.
tried using LSD download - the same problem FnA
it will be necessary to find a computer and try from it...because most likely the problem is in the adapter
thanks for the replies
Yes, I did, from the adapter.
tried using LSD download - the same problem FnA
it will be necessary to find a computer and try from it...because most likely the problem is in the adapter
thanks for the replies
-
- Автор сайта
- Posts:10238
- Joined:Tue May 30, 2006 20:17
- Location:Екатеринбург
- Has thanked: 134 times
- Been thanked: 556 times
- Contact:
Re: Converter USB-COM
Amauri
And, by the way, just in case: on the CD to the adapter there is a large list of folders with different connectivity options, so it is necessary to RS232 choose during installation. You can still try to demolish the installation and pereustanovit in the new.
And, by the way, just in case: on the CD to the adapter there is a large list of folders with different connectivity options, so it is necessary to RS232 choose during installation. You can still try to demolish the installation and pereustanovit in the new.
Re: Converter USB-COM
Andrey, tell me, and without the power cord session cannot be upgraded (from batteries)? I'm honestly surprised(((( also as an extra accessory is...
I tried all described instructions for installing... after adding sessions to the library click to load the library, and then do nothing.... on the machine screen is not responding...the program was thinking and all....like downloaded... No running lights, no FnA at InnerPulse...
I'm also using a com-usb adapter I tried.... the port he specified....
I need to separately purchase a power cord?
I tried all described instructions for installing... after adding sessions to the library click to load the library, and then do nothing.... on the machine screen is not responding...the program was thinking and all....like downloaded... No running lights, no FnA at InnerPulse...
I'm also using a com-usb adapter I tried.... the port he specified....
I need to separately purchase a power cord?
-
- Автор сайта
- Posts:10238
- Joined:Tue May 30, 2006 20:17
- Location:Екатеринбург
- Has thanked: 134 times
- Been thanked: 556 times
- Contact:
Re: Converter USB-COM
Lung
It is possible and on batteries. Only the batteries we sell pretty rested somewhere and therefore already hooked...
And the connection with the device installed?
It is possible and on batteries. Only the batteries we sell pretty rested somewhere and therefore already hooked...
Maybe everything is already loaded, have You checked?I tried all described instructions for installing... after adding sessions to the library click to load the library, and then do nothing.... on the machine screen is not responding...the program was thinking and all....like downloaded... No running lights, no FnA at InnerPulse...
And the connection with the device installed?
Re: Converter USB-COM
When I pressed test connection it gave me the message about the number of sessions possible, etc. Apparently he found the device. And then the picture is as I described.... Directory u appeared (((
Maybe someone can suggest a different cause.... System requirements PC not important? Folder I as it is written in the root of the C drive left.... I do not understand why does not work....
Maybe someone can suggest a different cause.... System requirements PC not important? Folder I as it is written in the root of the C drive left.... I do not understand why does not work....
-
- Автор сайта
- Posts:10238
- Joined:Tue May 30, 2006 20:17
- Location:Екатеринбург
- Has thanked: 134 times
- Been thanked: 556 times
- Contact:
Re: Converter USB-COM
And where he was supposed to appear?Легого wrote:Directory u appeared